MIBO Servo Waterproof 1:10 Onroad Brushless Low Profile (0,062s/14,5kg/8,4V)

Powerful and ultra fast programmable digital servo (waterproof) with low profile, brushless motor, steel gearbox and with double ball bearing output shaft is suitable for use especially in RC on-road car (Modified, Stock, FWD, Formula classes). The servo is placed in an aluminum housing, which ensures perfect cooling even under high load.

With KAVAN programming interface for Mibo servos and PC operating program, you can program a wide range of servo parameters.

Programmable functions:

Deflection size: Used to set the maximum size of servo deflections. The default setting is about 120° at the normal range of control pulse widths (900~2100 µs), about 180° at the maximum allowable range of control pulse widths (500~2500 µs).

Servo neutral position: Sets the neutral position (center position) of the servo.

Damping: Sets the characteristic of the servo behavior when stopping its movement.

Output Power: Sets the output power of the servo. The higher the value, the faster the servo and the higher the power - of course, the power consumption is also proportionally higher. Range: 39.2~100%

Sensitivity: Sets the sensitivity (insensitivity bandwidth) of the servo. The higher the value, the narrower the insensitivity bandwidth - the servo will move only if the change in control signal width is greater than the insensitivity bandwidth. If you set the sensitivity value too high, the servo may oscillate in some applications. Range: Ultra High (Extra high - insensitivity band approx. 1 µs) - High (High - approx. 2 µs) - Medium (Medium - approx. 3 µs) - Low (Low - approx. 4 µs)

Soft start: Switches the soft start function on/off. This function prevents the servo from abruptly going to the operating position after being connected to the power supply, thus reducing the risk of damaging its gear.

Servo Reverse: Reverses the servo deflections.

Mode FUTABA SR: Mode FUTABA SR: Only for use with channels of RC sets FUTABA operating in SR mode. Do not turn this option on if you are using a different setup of RC set FUTABA or a different brand of RC set.

SANWA SSR mode: Only for use with channels of RC sets SANWA operating in SSR mode. Do not turn this option on if you are using a different setup of RC set SANWA or a different brand RC set.

Fail-safe: If the control signal of the receiver fails completely or the servo cannot detect the signal correctly (e.g. due to interference), the servo can switch to one of three emergency modes:
(a) Free: Fail-safe is switched off.
(b) Hold position: The servo maintains the position corresponding to the last correctly received signal.
(c) Transition to neutral position: The servo returns to the neutral position (pulse width 1500 µs).

Overload protection: Activates or deactivates the servo overload protection in three stages - as soon as the overload persists for a preset time (in seconds), the servo output power is limited to the corresponding preset value (in % of the maximum power).

Reset: Restores the factory settings of the connected servo.

Features:

• Servo size: Low Profile
• Required servo horn: 25 teeth
• Servo type: Digital
• Programmable: YES
• Actuating force with 4.8V [kg/cm]: 10
• Actuating force with 6.0V [kg/cm]: 12
• Actuating force with 7.4V [kg/cm]: 13,5
• Actuating force with 8.4V [kg/cm]: 14,5
• Speed at 4.8V [s/60st.]: 0.085
• Speed at 6.0V [s/60st.]: 0.074
• Speed at 7.4V [s/60st.]: 0.068
• Speed at 8.4V [s/60st.]: 0.062
• Servo gear: Metal
• Ball bearing: 2
• High voltage: YES
• Power supply [V]: 4.8 - 8.4
• Length [mm]: 40.8
• Width [mm]: 20,2
• Height [mm]: 26,5
• Weight [g]: 57,2
• Cable length [mm]: 50
• Intended for: Onroad
• Waterproof: YES