MIBO Servo 1:8 Waterproof Brushless (0,085s/45kg,8,4V)

Extremely powerful and fast programmable digital standard servo 83g with brushless motor, steel gearbox and triple ball bearing output shaft is intended for use mainly in RC off-road cars 1:8. The servo is placed in a waterproof and dustproof (IP67 standard) aluminum housing, which ensures perfect cooling even under high load and protection from harsh operating conditions. The use of a magnetic encoder instead of the usual mechanical potentiometer also contributes to precise operation and high operational reliability.

With the KAVAN USB programmer/interface for MIBO servos and the PC operating program you can program a wide range of servo parameters.

Programmable functions:

Deflection size: Used to set the maximum size of the servo deflections. The default setting is about 120° at the normal range of control pulse widths (900~2100 µs), about 180° at the maximum allowable range of control pulse widths (500~2500 µs).

Neutral position of the servo: Used to set the neutral (center) position of the servo.

Damping: Adjusts the characteristic of the servo behavior when stopping its movement.

Output Power: Sets the output power of the servo. The higher the value, the faster the servo and the higher the power - of course, the power consumption is also proportionally higher. Range: 39.2~100%

Sensitivity: Sets the sensitivity (insensitivity bandwidth) of the servo. The higher the value, the narrower the insensitivity bandwidth - the servo will move only if the change in control signal width is greater than the insensitivity bandwidth. If you set the sensitivity value too high, the servo may oscillate in some applications. Range: Ultra High (Extra high - insensitivity band about 1 µs) - High (High - about 2 µs) - Medium (Medium - about 3 µs) - Low (Low - about 4 µs)

Soft start: Turns the soft start function on/off. This function prevents the servo from abruptly entering the operating position after being connected to the power supply, thus reducing the risk of damage to its gear.

Servo Reverse: Reverses the servo deflections.

FUTABA SR mode: Mode FUTABA SR: Only for use with channels of RC sets FUTABA operating in SR mode. Do not turn this option on if you are using a different setup of RC set FUTABA or a different brand of RC set.

SANWA SSR mode: Only for use with channels of RC sets SANWA operating in SSR mode. Do not turn this option on when using a different setup of RC set SANWA or a RC set of another brand.

Fail-safe: If the receiver control signal fails completely or the servo cannot detect the signal properly (e.g., due to interference), the servo can enter one of three emergency modes:
(a) Free: Fail-safe is off.
(b) Hold Position: The servo maintains the position corresponding to the last correctly received signal.
(c) Transition to neutral position: the servo returns to the neutral position (pulse width 1500 µs).

Overload Protection: Enables or disables servo overload protection in three stages - once the overload persists for a preset time (in seconds), the servo output power is limited to the corresponding preset value (in % of maximum power).

Reset: Restores the factory settings of the connected servo.

Features:

• Servo size: Standard
• Required servo horn: 25 teeth
• Servo type: Digital
• Programmable: YES
• Actuating force with 4.8V [kg/cm]: 28
• Actuating force with 6.0V [kg/cm]: 34
• Actuating force with 7.4V [kg/cm]: 39
• Actuating force with 8.4V [kg/cm]: 45
• Speed at 4.8V [s/60st.]: 0.14
• Speed at 6.0V [s/60st.]: 0.115
• Speed at 7.4V [s/60st.]: 0.10
• Speed at 8.4V [s/60st.]: 0.085
• Servo gear: Metal
• Ball bearing: 3
• High voltage: YES
• Power supply [V]: 4.8 - 8.4
• Length [mm]: 40
• Width [mm]: 20
• Height [mm]: 37,5
• Weight [g]: 83
• Cable length [mm]: 300
• Intended for: Offroad